When you want to show off your lawn, there is nothing nicer than having clear cut areas that define the separation between turf and flowerbeds or other formations. There are many towns and neighborhood associations that reward those that spend the time it takes to create a beautiful looking lawn. With a plastic bender board, you can create that clean separation with ease and keep the weeds from encroaching on your beds.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
The first step in placing them is to figure out how long they should be. One method is to place stakes at intervals along the path where they will be placed. Stretch a string between each stake and when finished, measure the length of the string. This prevents you from having to measure every angle and twist in the path and still be sure you have enough material. If you're unsure, add some inches to the final measurement.
Next, you want to dig the trench. Make sure it is at least six inches in width and deep enough to allow the board to sit below the surface. You will want to cover the board with dirt when you are done, so keep the dirt close by for the last step. For this process, you can place a piece of tape or paint on the shovel or keep a ruler handy to measure both the width and depth.
Put in the stakes. This process is important because it will hold the border in place. Put stakes every few feet or according to the manufacturer's suggestions. Where there is a break in the material, put in an extra stake to help hold the two ends together and prevent a gap.
The fourth step is to cut the material to length and place in the ground. It is easier if you roll the material out next to the trench. When done, make your cuts and slide the border into the hole and secure it to the stakes. This keeps it in place. If you notice any areas that are riding too high and will be exposed, just use a trowel and dig the dirt out from under it and place it to the side.
Use the dirt to fill the trench. Using a rake or shovel, fill in the trench until the dirt is all used up. There should be quite a bit left over and a nice mound will be on top. This fine since the dirt will settle in a few days. Pack it in by stomping on it or using a stamp or rake. After a few days of settling, you can begin to place stones on top if you want to create a nice visible border.
Once all of this is done your border will look great. Allow some time for the mound over the path to settle. If you are going to place rocks over it to beautify it, feel free to do that right away as this will help it settle faster. This will keep the weeds and turn from growing into the flower beds.
Two different types exist and are in use today. The first is made from packed wood fibers and other natural materials. Though it is a great way to create the border, it will have to be replaced over time because it is designed to decay and work its way into the soil. The plastic type will not decay over time and is environmentally sound because it is made of recycled plastics that would be headed to the landfill. It will last much longer and keep doing its job for years.
The first step in placing them is to figure out how long they should be. One method is to place stakes at intervals along the path where they will be placed. Stretch a string between each stake and when finished, measure the length of the string. This prevents you from having to measure every angle and twist in the path and still be sure you have enough material. If you're unsure, add some inches to the final measurement.
Next, you want to dig the trench. Make sure it is at least six inches in width and deep enough to allow the board to sit below the surface. You will want to cover the board with dirt when you are done, so keep the dirt close by for the last step. For this process, you can place a piece of tape or paint on the shovel or keep a ruler handy to measure both the width and depth.
Put in the stakes. This process is important because it will hold the border in place. Put stakes every few feet or according to the manufacturer's suggestions. Where there is a break in the material, put in an extra stake to help hold the two ends together and prevent a gap.
The fourth step is to cut the material to length and place in the ground. It is easier if you roll the material out next to the trench. When done, make your cuts and slide the border into the hole and secure it to the stakes. This keeps it in place. If you notice any areas that are riding too high and will be exposed, just use a trowel and dig the dirt out from under it and place it to the side.
Use the dirt to fill the trench. Using a rake or shovel, fill in the trench until the dirt is all used up. There should be quite a bit left over and a nice mound will be on top. This fine since the dirt will settle in a few days. Pack it in by stomping on it or using a stamp or rake. After a few days of settling, you can begin to place stones on top if you want to create a nice visible border.
Once all of this is done your border will look great. Allow some time for the mound over the path to settle. If you are going to place rocks over it to beautify it, feel free to do that right away as this will help it settle faster. This will keep the weeds and turn from growing into the flower beds.
About the Author:
When you are looking for information about plastic bender board, come to our web pages online today. More details are available at http://www.bestedging.com now.
No comments:
Post a Comment